Today, one of the significant objectives in MEP engineering design for HVAC design engineers is to improve energy efficiency, maintain air quality and thermal comfort. Energy efficiency, air quality and comfort in a building depend on how heating, cooling and air distribution systems are designed and this is where careful ductwork design plays a significant role. Ductwork and HVAC system design are important as it ensures indoor air quality, thermal comfort and ventilation. If the HVAC system and ducts are not designed accurately, it could lead to poor air quality, heat loss and make the conditioned space in the building uncomfortable.
The primary function of the ductwork design system is bim coordination services nyc to ensure a least obtrusive channel is provided through which cool and warm air can travel. When designed accurately, HVAC air distribution systems will play an important role in countering heat energy losses, maintaining indoor air quality (IAQ) and providing thermal comfort.
To understand how ductwork can be designed in a cost-effective and efficient manner, this article decodes ductwork design and provides a brief outline of the design process, methods and standards.
The basic principle of ductwork design is to heat, cool or ventilate a building in the most efficient and cost-effective way. The primary function of ductwork is to design conduits or passages that allow air flow to provide heating, cooling, ventilation and air conditioning (HVAC).
In the duct design process, the basics of air flow must be understood. Return air goes into an air handler unit (AHU), through a filter and into the blower and with pressure it goes through the A coil or heat exchanger and then it goes out into the supply air system. If the ductwork is designed correctly it enables the AHU to produce the right amount of air through the heat exchanger. In a typical air distribution system, ducts must accommodate supply, return and exhaust air flow. Supply ducts provide air required for air conditioning and ventilation, return ducts provide regulated air to maintain IAQ and temperature and exhaust air flow systems provide ventilation.
For ductwork design to be efficient, MEP engineering design teams need to have designers with a mechanical and engineering background. Ductwork design specialists or building service engineers must also possess thorough knowledge of other disciplines such as architectural, civil and structural concepts to ensure HVAC systems are clash free.
The ducting system design process is simple, provided that the specifications are clearly mentioned and the inputs regarding application, activity, building orientation and building material are provided. Based on the information provided calculations can be completed to create an energy-efficient and clash-free design. Typically, air conditioning and distribution systems are designed to fulfil three main requirements such as:
The process of ductwork design starts once architectural layouts and interior design plans are provided by the client or MEP consultants. Building service engineers then require specification requirements such as application, the number of people, the orientation of the building and architectural characteristics to make calculations on heat load and air flow. Before any calculations are carried out, single line drawings are drafted to showcase the flow of ductwork in the building. Once they are approved, calculations for heat load and air flow are conducted. Once the heat load calculations are complete, the air flow rates that are required are known and the air outlets are fixed. With the calculations, specifications and layout, the ducting system design layout is then designed taking into consideration architectural and structural details of the conditioned space and clashes with other building services such as electrical, plumbing (hydraulic) and mechanical services.
To start the ductwork design process there are inputs required regarding details about the type of application, specification requirements, building orientation, architectural characteristic and material.
• Application type – Ductwork design will vary based on the type of application the building will be used for such as manufacturing, data centres, medical applications, scientific research and comfort applications such as restaurants, offices, residences, institutional building such as schools and universities.
• Specification requirement – To create an efficient duct design, designers need to know what type of activity will be conducted and the average number of people that will use the conditioned space. This will help in calculating the air flow, velocity and heat load required to maintain temperatures and IAQ. In comfort applications, for instance, an office or restaurant will require different duct design and air velocity than a residence.
• Orientation and material of the building – The orientation of building and material used plays a key role in gauging heat absorption which will help determine the cooling and ventilation requirements. Based on whether a building faces north, south, east or west, and where it is geographically located, heat absorption can be calculated. The type of material used for construction also affects the amount of heat gain and loss of the building.
Ductwork design methods are usually determined based on the cost, requirements, specifications and energy efficiency standards. Based on the load of the duct from air pressure, duct systems can typically be classified into high velocity, medium velocity and low velocity systems. There are three commonly used methods for duct design:
1. Constant Velocity Method – This method, designed to maintain minimum velocity, is one of the simplest ways to design duct systems for supply and return air ducts. However, it requires experience to use this method as the incorrect selection of velocities, duct sizes and choice of fixtures could increase the cost. Moreover, to maintain the same rate of pressure drop in duct runs, this method requires partial closure of dampers in duct runs (except index run) which could affect efficiency.
2. Equal Friction Method – This conventional method used for both supply and return ducts maintains the same frictional pressure drop across main and branch ducts. This method ensures dissipation of pressure drops as friction in duct runs rather than in balancing dampers. However, like the velocity method, partial closure of dampers is required and this could lead to noise generation.
3. Static Regain Method – This method commonly used for large supply systems with long ducts is a high velocity system that maintains constant static pressure before each branch or terminal. While this is a balanced system as it does not involve dampering, longer ducts may affect air distribution to conditioned spaces.
While different duct design methods used vary from application to application, duct system performance and system balancing and optimisation need to be considered. After the air handling unit (AHU) is installed, the system needs to be balanced and optimised to enhance performance. In system balancing and optimisation, air flow rates of supply air outlets and return air inlets are measured, and dampers and fan speed are adjusted. Especially in large buildings, balancing air conditioning systems may be expensive and time-consuming, but it is required as it provides benefits that outweigh the cost incurred in installing the system. To minimise total and operating cost, many optimisation methods are used as such as the T-Method Optimisation described in the DA3 Application Manual of AIRAH (Australian Institute of Refrigeration Air Conditioning).
To design air distribution systems that are energy efficient and cost effective, HVAC system designs must include basic engineering guidelines and adhere to certain design standards. Let us consider some of the guidelines and standards used in the industry in different countries.
When designing air conditioning systems, HVAC design engineers must be knowledgeable about the basic methods, guidelines and standards applicable, from the type of units used, calculations required, methods of construction, type of material, duct system layouts, pressure losses, duct leakage, noise considerations to optimisation using testing, adjusting and balancing (TAB). Listed below are some of the standards organisations and associations in the U.S., U.K., Australia and India, that provide manuals, codes and standards for the HVAC industry.
SMACNA (Sheet Metal and Air Conditioning Contractors’ National Association) – It provides a manual on HVAC systems duct design that includes basic yet fundamental methods and procedures with importance on energy efficiency and conservation. While the manual does not include load calculations and air ventilation quantities, it is typically used in conjunction with the ASHRAE Fundamentals Handbook.
ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers) – It is an association that emphasises on the sustainability of building systems by focusing on energy efficiency and indoor air quality. The ASHRAE Handbook is a four-volume guide that provides the fundamentals of refrigeration, applications, systems and equipment. Updated every four years, the handbook includes international units of measurement such as SI (systems international) and I-P (inch-pound).